CSE466 Lab 1: “One-Minute Timer”

Objectives

Create a device that will count from 00 to 59 on two 7-segment led displays at a rate of 1Hz. When the end of the count is reached, it should wrap around and start counting from the beginning. There will be an example setup in the lab that you can use as a reference.

In this lab you will learn the following:

  • AVR assembly
  • Basics of the ATmega16 (Memory, registers, etc)
  • Binary to decimal 7-segment conversion
  • Become familiar with AVRStudio 4 (which has a simulator)
  • Programming and debugging with JTAG

Reading

Helpful Hints

  • Instruction set summary is on page 336-338 of the ATmega16 datasheet.
  • Detailed instruction descriptions available at Atmel's website. Please don't print out (150 pages) as the rest of your programming will be in C.  
  • General purpose registers are r0-r31, watch for instructions that only operate on some of them (ldi, load immediate, only works on r16-31)
  • Include [.include "m16def.inc"] to get logical names [PORTA] for registers (as opposed to having to use addresses [$3B])

Resources

 

Part 1: Wiring up the breadboard

  1. Read all of the directions for Part 1 before doing ANYTHING. Often the next step reveals why the current one is important.
  1. Wire the circuit in the schematic on your breadboard. Make sure the power is disconnected when wiring up your breadboard.
  2. The 7-segment LEDs displays are not connected to the ATmega16 in the schematic. You and your partner will need to decide how to connect the 8 wires from the ATmega16 to the 7-segment LED displays. The wiring pattern used should be exactly the same for both of the 7-segment displays allowing the same constant to be used when displaying numbers. Make sure you connect the decimal point of both 7-segment LEDs. Also note that the 7-segment LED displays combine to make the number (one will represent the tens digit and the other will represent the ones digit). To make the actual value of the counter easy to read it would be nice if the 7-segment LEDs were either next to each other or aligned so the bottom of the 7-segment LEDs were parallel.
  3. The resistors values have been purposefully left off the schematic. You will need to consult the datasheet to find the chip’s electrical characteristics to determine the appropriate values of the reset pull-up resistor and the current limiting resistors for the LEDs. For decent brightness the 7-segment LEDs should have around 5mA of current.

Question 1: There are 3 parts to this question to help you find a reasonable range for your pull-up resistor (HINT: A reasonable range is probably the same as the internal pull-up resistor). Even though the ATmega16 contains an internal pull-up resistor the goal of the question is to review how to calculate a reasonable range for chips that do NOT have an internal pull-up resistor. Keep in mind that you want to have large safety margins when choosing the pull-up resistor to use in your reset circuit.

 

a. Calculate the range of resistance values for the reset pull-up resistor. Refer to the schematic to visualize the circuit in question.

The minimum resistor value must be calculated for the case when the reset switch is closed.  When this switch is closed, Vcc and ground are connected directly through the pull-up resistor. The maximum current draw is limited by the 1/4 W resistors we use in this class. Calculate the min resistor value given this information. Remember V = I * R and Power = V * I.

The maximum resistor value must be calculated for the case when the reset switch is open. The minimum voltage for which the reset pin is considered high can be found on page 291. For the reset circuit to function properly, the pull-up resistor must allow at least a minimum amount of current to flow to the chip. A good indication of what this minimum current should be is the maximum input leakage current for I/O pins listed on page 291. Using the value of Vcc, minimum reset high voltage and minimum input current values, calculate the max resistor value.

What is the theoretically largest possible range from the values you calculated? (List the min/max values) In practice a more reliable system will narrow the range significantly to minimize the risk of failure due to changing conditions.

b. The ATMega16 includes an internal reset pull-up resistor, what is the range of this resistor as specified in the datasheet (see page 291)?

c. Choose a pull-up resistor that is within the acceptable range for the internal pull-up resistor. What resistance value did you choose?

Question 2: Calculate the theoretical amount of current flowing through a single segment of the 7-segment LEDs when it is illuminated.  In your calculation use only values from datasheets or labels. Do not use any measured values in your calculation.

  1. Before powering on the breadboard, verify with a multimeter that there are no shorts between power and ground, and that power and ground are actually hooked up to the chips' pins.
  2. Turn on the JTAG interface and power up your breadboard.
  3. To verify that your hardware is working properly, program your wired up breadboard with flash.hex. (This program should cause your 7-sement LEDs to flash “88”). The ATmega16 can be programmed directly with the development environment called AVR Studio 4 that we’ll be using for half of the quarter.  To do so:

a)      Open AVR Studio 4. If you’re presented with a dialog box like the one pictured below, click the cancel button, since you are not creating your own program yet.

b)      Click the Con button on the toolbar, highlighted below:

conn

c)      Select JTAGICE mkII as the platform, and Auto as the port:

avrprog

d)     Select the ATmega16 as the device, and make sure that JTAG is selected as the programming mode. If “Verify Device After Programming” is checked, “Erase Device Before Programming” must also be checked!

prog

e)      Under the Flash section, press the program button, navigate to where you saved the flash.hex file, and click OK.

f)        Assuming all goes well, your board should begin flashing “88” in a few seconds.

Part 2: Create a simple program in Assembly

  1. Read all of the directions for Part 2 before doing ANYTHING. Often the next step reveals why the current one is important.
  1. Select New Project from the Project menu.

 

  1. The Project Type is “AVR Assembler”. Give the project a name and change the location to a lab partner’s network share. Then, hit next.

 

 

  1. Select “JTAGICE mkII” as the Debug Platform and “ATmega16” as the Device then hit finished.

 

platform-options

 

  1. Copy the following code to the assembly file. (The code should display an “8” on one of the 7-segment LEDs)

 

.include "C:\Program Files\Atmel\AVR Tools\AvrAssembler\Appnotes\m16def.inc"

.cseg

ldi r16, 0xff

out DDRB, r16

ldi r16, 0x00

out PORTB, r16

loop:

jmp loop

 

  1. From the Project menu choose "Assembler options". Change Version 2 to Version 1. You will get a build error otherwise.
  2. Build and run the project by selecting “Build and Run” from the Project menu, or hit Ctrl-F7. This will cause the program to stop at the first instruction. To run the program, select “Run” from the Debug menu, or press F5.

 

  1. Modify the code to determine the constants needed to generate the other 9 numbers on the 7-segment LED displays.

Part 3: Create a BCD Counter in Assembly

Read all of the directions for Part 3 before doing ANYTHING. Write a program in assembly that will count from 00 to 59 on two 7-segment led displays (one will be the tens digit and the other will be the ones digit). Implement a lookup table in program memory to convert a 4-bit nibble (in binary) to a decimal number.  Use this skeleton program as a starting point. If you want to use AVR Studio 4’s debugger, read this tutorial.

Requirements:

  1. Use a lookup table in program memory to store the constants needed to generate the 10 digits (‘0’-‘9’) on a 7-sement LED. You will need to use the LPM instruction to load the constant from program memory. NOTE: The ATmega16 uses 16-bit instructions even though it is an 8-bit processor; therefore, the 256th instruction is actually located at memory address 512 and 513. Keep this in mind when declaring your constants in program memory. The code/instructions are two bytes wide (16 bits) but when the program accesses the program memory it can only access one byte (8 bits) at a time causing the number of addresses to be doubled.
  2. The decimal point segment on the ones-digit 7-segment LED display should toggle on every change of counter value. The decimal point on the tens-digit display may be set arbitrarily. If you’re clever, you can take advantage of this fact to make your code smaller.
  3. Counting should happen at 1 Hz.


Question 3: Prove that you are counting at a rate of 1Hz through calculations by using the number of cycles each instruction takes. In the case of branches where a variable number of cycles may result, you may assume that the most frequent branch is taken. Please show your work and list any assumptions you made.

Deliverables

Submit the files through Catalyst Tools at:

·         AA section

·         AB section

Demonstrate your working system to a TA. You can either do this during this lab, or during the first
1/2 hour of the next lab. Counting should happen at 1 Hz. 

Turn in the answers to the three lab questions and a soft copy of your commented assembly code.

  • Please turn in the answers to the questions in an easily readable format. RTF, TXT, or PDF files are preferred. MS Word files are okay, but please save them as .doc and NOT .docx!