CM: CM: Warning L-1/C0 : #0 Warning: The net '/MemControl/ReadA' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: Synthesis successful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: Symbol 'MEMCONTROL' successfully created CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: Warning L-1/C0 : #0 Warning: The net '/MemControl/ReadA' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully created CM: CM: Synthesizing... CM: Error L31/C0 : #0 Error: syntax error at or near token '}' (File: Z:/ammerman/cse567/Working/vgacam/camera_test.v Line: 31) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Synthesizing... CM: Error L11/C0 : #0 Error: Undefined variable 'equals' used near symbol "=" on line 11 in file equals8.v (VE-3) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L11/C0 : #0 Error: Undefined variable 'equals' used near symbol "=" on line 11 in file equals8.v (VE-3) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'EQUALS8' successfully created CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'EMPTY' successfully created CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'EMPTY' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: Warning L10/C0 : #0 Warning: Variable 'reset' is being read in routine empty line 10 in file 'Z:/ammerman/cse567/Working/vgacam/empty.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: 0 error(s) 1 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'EMPTY' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'EMPTY' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'EMPTY' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'EQUALS' successfully created CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'EQUALS' successfully updated CM: Warning L-1/C0 : #0 Warning: The net '/MemControl/ReadA' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L76/C0 : #0 Error: Undefined macro `FR at or near token '`FR' (File: F:/cse567/John/test/vgacam/camera_test.v Line: 76) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '5' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L9/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 9) called from file F:/cse567/John/test/vgacam/camera_test.v (line 157) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '3' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L8/C0 : #0 Error: syntax error at or near token '4' (Macro: F:/cse567/John/test/vgacam/camera_test.v Line: 8) called from file F:/cse567/John/test/vgacam/camera_test.v (line 156) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L152/C0 : #0 Error: Cannot assign to constant 'FR' near symbol ":" on line 152 in file camera_test.v (VE-5) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesis Successful CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L123/C0 : #0 Error: Cannot assign to constant 'FR' near symbol ":" on line 123 in file camera_test.v (VE-5) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Checking... CM: Error L92/C0 : #0 Error: Undefined variable 'next_DataOut' used near symbol "=" on line 92 in file camera_test.v (VE-3) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L96/C0 : #0 Error: Cannot assign to constant 'WRITE' near symbol "=" on line 96 in file camera_test.v (VE-5) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Check Successful CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<3>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<1>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<4>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<7>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<6>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<2>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<5>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<0>' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 8 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<1>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<5>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<7>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<3>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<4>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<2>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<6>' is a feed through net. (FPGA-CHECK-9) CM: Warning L-1/C0 : #0 Warning: The net '/camera_test/DataIn<0>' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 8 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'camera_test' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 1 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Synthesis Successful CM: Use Synthesis/View Report for detailed synthesis report CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L54/C0 : #0 Error: syntax error at or near token 'else' (File: I:/CSE567/CARL/WORKING/VGACAM/camera_test.v Line: 54) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: Warning L40/C0 : #0 Warning: Variable 'inImage' is being read in routine camera_test line 40 in file 'F:/cse567/Carl/Working/vgacam/camera_test.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: 0 error(s) 1 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L38/C0 : #0 Error: syntax error at or near token '=' (File: F:/CSE567/CARL/WORKING/VGACAM/bankselect.v Line: 38) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L38/C0 : #0 Error: syntax error at or near token '=' (File: F:/CSE567/CARL/WORKING/VGACAM/bankselect.v Line: 38) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L71/C0 : #0 Error: syntax error at or near token 'endmodule' (File: F:/CSE567/CARL/WORKING/VGACAM/bankselect.v Line: 71) (VE-0) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'bankselect' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 1 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BANKSELECT' successfully updated CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'bankselect' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 1 warning(s) found CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BANKSELECT' successfully updated CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: CM: Checking... CM: Error L30/C0 : #0 Error: Port 'frameEnd' used before being assigned a direction near symbol "=" on line 30 in file camera_test.v (VE-12) CM: 1 error(s) 0 warning(s) found CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMERA_TEST' successfully updated CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: Warning L-1/C0 : #0 Warning: The net '/MemControl/ReadA' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: CM: Checking... CM: Check Successful CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BANKSELECT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BANKSELECT' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: Error L7/C0 : #0 Error: syntax error at or near token 'Write' (File: C:/cse467/projects/vgacam/CamCntl.v Line: 7) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L32/C0 : #0 Error: Undefined variable 'Clk' used near symbol ")" on line 32 in file CamCntl.v (VE-3) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L45/C0 : #0 Error: Undefined variable 'RE' used near symbol "=" on line 45 in file CamCntl.v (VE-3) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CAMCNTL' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BANKSELECT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Error L28/C0 : #0 Error: Undefined variable 'PixelData' used near symbol "=" on line 28 in file CrossHairs.v (VE-3) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L28/C0 : #0 Error: syntax error at or near token ')' (File: D:/Cam/VGACAM/CrossHairs.v Line: 28) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Warning L-1/C0 : #0 Warning: The net '/CrossHairs/blankOut' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CROSSHAIRS' successfully updated CM: CM: Warning L-1/C0 : #0 Warning: The net '/CrossHairs/blankOut' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: Synthesis successful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Warning L-1/C0 : #0 Warning: The net '/CrossHairs/blankOut' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: Synthesis successful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Warning L-1/C0 : #0 Warning: The net '/CrossHairs/blankOut' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: Synthesis successful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L116/C0 : #0 Error: Illegal assignment to wire 'BrightRow' near symbol "=" on line 116 in file LaserSpot.v. (VE-7) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Warning L112/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: 0 error(s) 9 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Warning L112/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: 0 error(s) 9 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Warning L112/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: 0 error(s) 9 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Warning L112/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: 0 error(s) 9 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Checking... CM: Check Successful CM: CM: Synthesis Successful CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L15/C0 : #0 Error: Illegal assignment to wire 'DataOut' near symbol "=" on line 15 in file BLANKPIXEL.v. (VE-7) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BLANKPIXEL' successfully updated CM: CM: Synthesizing... CM: Warning L112/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: 0 error(s) 9 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Warning L112/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: 0 error(s) 9 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L112/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 112 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 14 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Warning L-1/C0 : #0 Warning: The net '/CrossHairs/blankOut' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: Synthesis successful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesis Successful CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Warning L-1/C0 : #0 Warning: The net '/CrossHairs/blankOut' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: Synthesis successful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesis Successful CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Warning L-1/C0 : #0 Warning: The net '/CrossHairs/blankOut' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: Synthesis successful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesis Successful CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Warning L31/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 15 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Warning L31/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 7 warning(s) found CM: Synthesis successful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Warning L31/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 7 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L31/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 7 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L31/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L31/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 31 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 118 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 8 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L28/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L115/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 115 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L115/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 115 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 8 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L28/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L115/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 115 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L115/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 115 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 8 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L28/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L115/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 115 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L115/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 115 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 8 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L28/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L28/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 28 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L115/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 115 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L115/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 115 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 8 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 8 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 15 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 13 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 11 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 9 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 7 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 7 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 7 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Operation failed CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 9 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: Warning L-1/C0 : #0 Warning: The net '/CrossHairs/blankOut' is a feed through net. (FPGA-CHECK-9) CM: 0 error(s) 1 warning(s) found CM: 0 error(s) 0 warning(s) found CM: Warning L29/C0 : #0 Warning: Variable 'CameraBank' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'PixelData' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'RowAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L29/C0 : #0 Warning: Variable 'ColAddr' is being read in routine LaserSpot line 29 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'MonitorBank' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L116/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 116 in file 'D:/Cam/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 9 warning(s) found CM: CM: Synthesizing... CM: Warning L29/C0 : #0 Warning: Variable 'CameraFrame' is being read in routine LaserSpot line 29 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L117/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 117 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L117/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 117 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L117/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 117 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L117/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 117 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L117/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 117 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L117/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 117 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L117/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 117 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L117/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 117 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L-1/C0 : #0 Warning: Latch inferred in design 'LaserSpot' read with 'hdlin_check_no_latch'. (HDL-307) CM: 0 error(s) 10 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CROSSHAIRS' successfully updated CM: CM: Synthesis Successful CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L12/C0 : #0 Error: syntax error at or near token 'output' (File: D:/CamNew/VGACAM/LaserSpot.v Line: 12) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Warning L118/C0 : #0 Warning: Variable 'Row0' is being read in routine LaserSpot line 118 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Row1' is being read in routine LaserSpot line 118 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Row2' is being read in routine LaserSpot line 118 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Col1' is being read in routine LaserSpot line 118 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Row3' is being read in routine LaserSpot line 118 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Col3' is being read in routine LaserSpot line 118 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Col0' is being read in routine LaserSpot line 118 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: Warning L118/C0 : #0 Warning: Variable 'Col2' is being read in routine LaserSpot line 118 in file 'D:/CamNew/VGACAM/LaserSpot.v', but does not occur in the timing control of the block which begins there. (HDL-180) CM: 0 error(s) 8 warning(s) found CM: Synthesis succesful (Warnings found) CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Error L52/C0 : #0 Error: A reg can only be assigned with all RTL assignments or all procedural assignments near symbol ";" on line 52 in file LaserSpot.v. (VE-57) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L71/C0 : #0 Error: A reg can only be assigned with all RTL assignments or all procedural assignments near symbol ";" on line 71 in file LaserSpot.v. (VE-57) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesis Successful CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: Error L2/C0 : #0 Error: syntax error at or near token 'LaserPoint' (File: D:/Cam/VGACAM/CrossHairs.v Line: 2) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L26/C0 : #0 Error: syntax error at or near token '@' (File: D:/Cam/VGACAM/CrossHairs.v Line: 26) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L30/C0 : #0 Error: Illegal assignment to wire 'PixelDataOut' near symbol "=" on line 30 in file CrossHairs.v. (VE-7) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L30/C0 : #0 Error: syntax error at or near token 'assign' (File: D:/Cam/VGACAM/CrossHairs.v Line: 30) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L31/C0 : #0 Error: Illegal assignment to wire 'PixelDataOut' near symbol "=" on line 31 in file CrossHairs.v. (VE-7) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CROSSHAIRS' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Error L113/C0 : #0 Error: Illegal assignment to wire 'LaserPoint' near symbol "=" on line 113 in file LaserSpot.v. (VE-7) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: Error L114/C0 : #0 Error: syntax error at or near token 'assign' (File: D:/Cam/VGACAM/LaserSpot.v Line: 114) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L114/C0 : #0 Error: Illegal assignment to wire 'LaserPoint' near symbol "=" on line 114 in file LaserSpot.v. (VE-7) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L115/C0 : #0 Error: Illegal assignment to wire 'LaserPoint' near symbol "=" on line 115 in file LaserSpot.v. (VE-7) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L115/C0 : #0 Error: syntax error at or near token 'assign' (File: D:/Cam/VGACAM/LaserSpot.v Line: 115) (VE-0) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: Error L114/C0 : #0 Error: Illegal assignment to wire 'LaserPoint' near symbol "=" on line 114 in file LaserSpot.v. (VE-7) CM: 1 error(s) 0 warning(s) found CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CROSSHAIRS' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BLANKPIXEL' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'LASERSPOT' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CROSSHAIRS' successfully updated CM: CM: Synthesis Successful CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BLANKPIXEL' successfully updated CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: 0 error(s) 0 warning(s) found CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CROSSHAIRS' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BLANKPIXEL' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'CROSSHAIRS' successfully updated CM: CM: Synthesizing... CM: CM: Use Synthesis/View Report for detailed synthesis report CM: CM: Netlist is up-to-date CM: Symbol 'BLANKPIXEL' successfully updated